The PIP5 is a highly integrated robust Industrial PC with a special designed EMC protected aluminum housing. The design integrates standard connectors for easy connection and inexpensive installation. The unit can be used for any PC Application where a complete solution is needed.
The PIP5 can be used in a standard or in a rugged operating environment and is 100% PC/AT compatible.
The PIP housing offers space for a hard disk or expansion if needed on the PC/104. Fully bootable Flash Disks are support for project where hard disks or floppy cannot be used.
Special efforts have been taken on the quality of the components and its long term availability (5 years). Another PIP specialty is the extreme low power consumption of the system. This allows to operate the system without fan or ventilation holes. Further can the PIP5 be used in applications where extended temperature is a must.
Certainly special precaution have been taken on the EMC on the total system to fulfill the CE and FCC requirements.
All these features and its reasonable cost make the PIP5 to the ideal solution for the industry where a flexible, rugged long term available complete Industrial PC is needed.
|Processor||AMD Elan™SC520, 32-Bit low power CPU,133MHz||Industry-standard Am5x86-133MHz, 16kbytes write-back/through cache|
|BIOS||256kB Flash EEPROM, easy update||MPL engineered BIOS (General Software)|
|SDRAM||168-pin DIMM module socket||Up to 256MB SDRAM|
|FLASH||44-pin header for IDE Flash modules||Up to 1GB Flash, bootable|
|Multi Purpose Socket||Supports SRAM, FLASH, EPROM||28 & 32-pin DIL, up to 512kB memory size|
|RTC & CMOS-RAM||backed with on-board battery, field exchangeable||CMOS setup can be saved in EEPROM|
|SVGA Interface||C&T69000 video accelerator
resolution up to 1280 x 1024
flexible panel support for STN, TFT
|15-pin D-SUB connector
refresh rate up to 85Hz
50-pin remote MMi module socket
|4 x Serial Ports||2 ports can be modified optionally to
half & full duplex, electrically fully isolated
|2 x 9-pin D-SUB and
1 x 25-pin D-SUB connector
|2 x USB Ports||USB 1.1 (up to 12Mb/s)||2 x Type A connector|
|Parallel Port||config. as LPT1...3, SPP,EPP, ECP (IEEE1284)||25-pin D-SUB connector|
|E-IDE Port||ANSI Standard mode 0, 1 and ; up to 4 drives||Standard 44-pin & 40-pin header|
|FDD Port||One port for up to 2 drives||Connection for internal or external device|
|CAN Bus||Opto-isolated CAN Bus interface (CAN Spec. 2.0)||9-pin D-SUB connector|
|Expansions||full 16-bit PC/104 and full 32-bit PC/104+ interface|
|Speaker Port||Easy connection of speaker||internal 4-pin header|
|Keyboard||PS/2 interface||6-pin mini DIN connector|
|Mouse||PS/2 interface||6-pin mini DIN connector|
|Watchdog||distinct keyed write sequence||Programmable time-out|
|Timer||Two 16/32-bit TTL Timer output signal||available over 4-pin header|
|Indicator||6 activity LED's + 2 user definable||Power, Reset, HDD, SCSI, LAN, LAN100|
|Reset Button||On chassis (protected) and a remote reset button|
|SCSI Interface||ASPI, SCAM and Fast SCSI compatible||50-pin SCSI-2 connector|
|Ethernet||10BaseT / 100BaseTX
supports IEEE802.3 auto negotiation
|Physical / Power|
|Chassis||Rugged chromated aluminum chassis with best EMI protection, also after years||DIN-rail, wall mounting, desk top version|
|Size & weight (standard)||270 x 162 x 62mm (L x W x H) / 2.2kg||10.6 x 6.4 x 2.4 inch / 4.85 pounds|
|Power||On boards high efficiency switching regulator||8 - 28VDC supply power|
|Power consumption||typically < 7 Watts||12VDC, 133MHz, 64MB SDRAM, 10GB HDD|
|Temperature Range||-20°C up to 60°C, optional -40°C up to 75°C||No fan or opening in housing are required|
|Humidity||5% - 95% non condensing||Optional coating available|
|The PIP5 is designed to meet or exceed the most common standards. Particular references are:|
|EMC||EN 55022, EN 55024, EN 61000, MIL-STD-461E|
|Shock & Vibration||EN 60068|
|Environmental & Safety||EN 50155, MIL-STD-810-F, EN 60601, EN 60950|
|Approval Lists||CE, IEC 60945, IACS E10|
|PIP5-1||Low Power 5x86-133MHz CPU (ELAN520) with on-board CAN, SXGA, 2x USB1.1, 4x RS232, 10/100 Ethernet, SCSI-2, PC/104....|
|PIP5-2||Low Power 5x86-133MHz CPU (ELAN520) with on-board CAN, SXGA, 2x USB1.1, 4x RS232, 10/100 Ethernet, PC/104....|
|PIP5-Cx||PIP Solution assembled & mounted according to customer needs & requirements (e.g. with or without housing, depopulated parts, installation of specific connectors, installing a customers application, etc.)|
|XTEST-2||extended temperature test -40° C up to +75° C|
For deployment in harsh environments, the PIP5 can be ordered in an extended temperature version.
Every system needs to pass various tests in a environmental chamber to prove that it will perform flawless
over the temperature range indicated.
Please note: In order to get a system that will operate under these conditions, all additional selected components like hard disks or extension cards have to be specified or tested for conformity to the extended temperature range.