Rugged MIL/COTS SWaP-C Server - MXCS-15xxML-C1
conductive cooled, with Intel Xeon CPUs

[Rugged MIL/COTS SWaP-C Server]

The MIL/COTS SWaP-C Server Solution was designed with the target to meet the MIL-STD-810 as well as parts of the DO-160 standards. The solution is installed in a compact IP67 housing with a total of eigth D-38999 connectors including a dual fiber optical 10Gbit LAN port.

The MPL engineering approach has been taken very differently to most rugged solution in the market. The internal wiring has been eliminated as much as possible. The D38999 MIL connectors are soldered on special MPL designed rigid-flex PCBs. The EMI protection in each interface is integrated directly the connector on the PCBs. This will give best EMI efficiency and interface quali

The MXCS-15xxML-C1 comes with numerous interfaces like DVI-D, USB 2.0, serial lines, LAN, 10Gbit fiber LAN as well as a wide power input. Additional expansions (CAN, 1553, ARINC...) can be done over the internal expansion interfaces such as mPCIe, m.2, PCIe or PCIe/104, These expansions can be done easy, and quickly be integrated into the system.

To interface to the standard embedded CPU board from MPL, mating interfaces boards (ICC) have been designed. The flex part of the connector PCBs are connected to the ICC which is interfacing cable free directly to the CPU board.

Key features are: * depending on selected CPU

With this concept, the MXCS can basically meet any specification in rugged computing environments specified in various MIL standards. The CPU board as well as the ICC and connector PCBs can be coated and bonded to increase the robustness even further.

pdf

Technical Features

Board Key Data
Processor Intel Xeon D-1548 Intel Xeon D-1577 Intel Xeon D-1587
Clock speed 2.0 / 2.6GHz 1.3 / 2.1GHz 1.7 / 2.3GHz
Cores / threads 8 / 16 16 / 32 16 / 32
Smart cache 12 MB 24 MB 24 MB
TPM 2.0 TPM 2.0 with EAL4.0 optionally supported
Memory Up to 128 GB ECC DDR4 can be installed
Mass Storage The solution provides the following interfaces: 2 x m.2,  2 x mSATA, 2 x SATA (removable or fixed)
If a RAID configuration is needed, then this can be configured as well
BMC The MXCS-ML has integrated an independent BMC. The sytem comes with redundant AMI Boot Flash
Interfaces
The selected connectors in this solution are: (other connectors or interfaces are possible)
Power TVP02RW-9-35PN ( 6-pin ) LAN TVP02RW-15-35SN ( 37-pin )
Serial TVP02RW-13-35SN ( 22-pin ) LAN RJFTV22G00 ( RJ45 )
USB2.0 USBFTV71ZN (USB) LAN RJFTV22G00 ( RJ45 )
BMC TVP02RW-15-35SA ( 37-pin ) 10GBit M28876/1B1S1
Power
Input Voltage 19 - 36VDC input voltage range, ESD and EMC protected / Ignition input specifically for vehicles
Optional MIL-STD-1275D and/or MIL STD-704F
Optional internal UPS system, optional galvanic separation, other voltage possible
Power Consumption Complete system 40-100 Watt (depending on CPU and RAM), Enhanced Intel Speed Step Technology
Environment
Storage Temperature -45°C up to +85°C
Operating Temperature -20°C up to +60°C, fanless (extended temperature are optionally possible)
Relative Humidity 5% to 95% non condensing, optional coating available
Schock 3 shocks in each dir. of the 3 axes, 35g, 18ms, half sine/ final peak saw tooth/ trapezoidal
Vibration broad-band random (operating) 10Hz-250Hz, 5.4m/s2, 10 minutes
Vibration broad-band random (operating after shock) 10Hz-250Hz, 42.5m/s2, 5 hours
Dimension 296 mm x 220 mm x 66 mm
Standard Compliance
The MXCS-15xxML-C1 is designed to meet or exceed the most common standards. Particular references are:
EMC EN 55022, EN 55024, EN 61000, MIL-STD-461E
Shock & Vibration EN 60068
Environmental & Safety EN 50155, MIL-STD-810G, EN 60601, EN 60950
Approval List CE, IEC 60945, IACS E10

Specifications subject to change without notice


 Copyright © 1997-2021 MPL AG Elektronikunternehmen, a member of the HT Holding AG  |  Privacy Statement
MPL on LinkedIn    MPL on twitter